spinneret
Filter and spinneret pack can be easily replaced.
过滤器和喷丝头组件可以容易的替换。
Many tiny tubes connect each silk gland with a spinneret.
许多极细小的导管把每个造丝腺体与吐丝器相连。
The tantalum spinneret is a key part in chemical fibre silk spinning_machine.
喷丝头是化纤纺织机上的关键部件。
The solution is filtered and prmped through the fine holes of a spinneret.
纺丝液经过滤后，借助于泵的压力穿过喷丝头的细孔。
The recovery process of monomer smoke at strand spinneret from nylon6 production was analyzed.
分析比较了尼龙6生产中注带处单体烟的几种回收方法。
Usually the number of holes in the spinneret determines the number of filament in the yarn.
一般喷丝头细孔的数量决定了纱中长丝的根数。
The practical experiments showed that fiber spinnability was optimized when spinneret negative draw ratio was -73%.
工业化试验表明:当喷丝头负拉伸率为-73%时,纤维可纺性达到最佳状态。
In this system,the image of the holes on the spinneret were zoomed in and stored for post-processing.
该系统通过显微镜对喷丝孔进行放大成像并采集保存。
PET POY with different linear density and orientation can be produced with the same spinneret.
利用具有不同孔径的同一喷丝板生产不同线密度和取向度的涤纶POY。
Trilobal polycarbosilane(PCS) fibers were prepared by melt spinning PCS precursor through Y shaped spinneret.
以聚碳硅烷(PCS)为原料,采用熔融纺丝制备三叶型PCS纤维后,经不熔化和烧成制得三叶型碳化硅纤维。
And also effect of spinneret draw-ratio on fibre aggregated structure and the properties was discussed.
分析喷丝头拉伸比对纤维的聚集态结构及性能的影响。
Nylon is meltspun. That is to say a molten mass.of nylon, formed by melting nylon chips, is forced through holes in a spinneret.
尼龙是采用熔纺工艺制成的,即将由熔化的尼龙切片构成的尼龙熔融体,强制通过喷头的纺丝孔
Nylon is meltspun. That is to say a molten mass of nylon, formed by melting nylon chips, is forced through holes in a spinneret.
尼龙是采用熔纺工艺制成的,即将由熔化的尼龙切片构成的尼龙熔融体,强制通过喷头的纺丝孔
The paper states the feature and technical innovation of the spinneret pack on NOY high speed spinning machine, as well as results of its application.
本文介绍了NOY高速纺丝机纺丝组件的结构特征，结合生产提出技术改造方案及其生产应用情况。
Some factors influencing upon the primary fiber forming are discu ssed,such as the conditions of spinning and the type of the spinneret micro-ho le.
重点讨论了喷丝板微孔孔形及纺丝工艺条件对初生纤维成型的影响。
The company on the production of the textile industry mainly spinneret, according to the needs of customers can produce all types spinneret.
公司主要以生产纺织业上喷丝板为主，按客户的需要可以生产各种类型喷丝板。
Nylon is meltspun.That is to say a molten mass of nylon, formed by melting nylon chips, is forced through holes in a spinneret.
尼龙是采用熔纺工艺制成的，即将由熔化的尼龙切片构成的尼龙熔融体，强制通过喷丝头的纺丝孔。
The size of the filament depends on the rate of flow through the hole of the spinneret rather than on the size of the hole.
所制成长丝的直径取决于粘胶在喷丝头孔中的流速，而不取决于孔径的大小。
It was p ointed out that the fiber denier and spinneret should be taken into consideratio n while selecting spinning velocity.
调整生产能力要根据产品纤度、现有喷丝板的情况来选择适当的纺丝速度，也可通过改变喷丝板孔数来实现。
In this paper, the influence factors of spinning acetate fiber by the dry process using Y type spinneret of 0. 04-0. 03-500 holes were analysed.
本文分析了500孔Y形喷丝板于纺二醋纤的影响因素，认为在纺丝溶液中加入适量的助剂A对纺丝有利；
The effects of spinneret hole shape, characteristic dimension of spinneret ,hole arrangement and cool conditions on degree of profile were discussed.
异形喷丝孔的当量直径、截面积、孔长等特征尺寸决定了熔体在喷丝孔中的流变行为，建议采用当量异形度作为纤维的异形度指标。
The more resonable the capillary confiyura non of spinneret.the better the spinnability.when designing spinneret,we shou...
因此，在设计过程中要综合考虑喷丝板结构各参数，此外，还讨论了结构不同的三种异形喷丝板的清洗方法和效果以及其使用寿命。
The effect of spinneret hole diameter on the filament diameter and birefringence of PET POY was studied by using the same spinneret.
具体分析了喷丝孔直径与剪切速率及喷丝头拉伸倍数之间的关系，提出了喷丝孔直径的选择依据。
Shine and flat polyester staple fiber was produced by using profiled spinneret and special spinning and drawing process.
通过异形喷丝板的设计及特殊纺丝和后拉伸工艺生产了闪光扁平涤纶短纤维。
The bright profiled PET can be produced by the forming technology ex truded from the spinneret slit and high-speed spinning-drawing with bright p olyester chips.
介绍了以超有光聚酯切片为原料,采用熔体狭缝挤出成型技术和高速纺丝牵伸一步法工艺制取异形PET纤维的生产方法。
While increasing the diameter of spinneret hole, the filament diameter of PET POY was increased, both the orientation and the birefringence of PET filament were decreased.
随着喷丝孔孔径的增大,涤纶POY单丝直径增大,单丝的取向度降低,双折射率减小。
Using NaSCN as solvent,acrylic fiber was produced by one-step wet spinning process.The effect of spinneret negative draw ratio on fiber formation was discussed.
采用硫氰酸钠为溶剂,湿纺一步法工艺生产腈纶,探讨了喷丝头负拉伸率对纤维成形的影响。
Floss spinning, wool spinning and chemical fiber equipment such as : combine, drawing frame, floss comber, fiter, carding machine, spinneret, measure pump, etc.
棉纺类有清梳联合机、并条机、棉精梳机及滤尘设备；毛纺类有梳理机、制条机、精纺成套设备；化纤类有喷丝头、计量泵、混条、制条等设备。
The reason for plugging the spinneret was analyzed.The cleaning methods were also introduced in details.TEG was used for cleaning the melt distribution channels of POY device.
用三甘醇清洗堵塞的POY装置熔体管道，分析了熔体管道堵塞的原因，详细介绍了清洗方法。
In this paper.the relationship between capillary configuration ot spinneret and spinnability was studied under POY-DT production of lustrous "Y"- fiber.
本文讨论了在三叶有光POY-DT生产过程中，喷丝板毛细孔尺寸与可纺性的关系。
A manufactured fiber formed by compound of cellulose, refined from cotton linters and/or wood pulp, and acedic acid that has been extruded through a spinneret and then hardened.
一个制造纤维所形成的复合纤维素，完善由棉短绒和/或木浆，和acedic酸已被挤压通过喷丝板，然后硬化。
Electrospinning works by connecting a needle-like spinneret to a high-voltage power source and releasing a charged liquid from it towards an earthed collector plate.
电纺的工作方式是将一根针状喷丝头连上高压电源并从中对一个接地的收集器释放出一股带电液体。
There are many methods to produce blended yarn, but to produce blended yarn through one spinneret is more economical and with better effects compared with other methods.
目前多异混纤纱的生产方法有多种,但是较之其他多种方法,利用同板生产则更具经济性和良好的效果。
The result indicates that the desired flat-like polyester filaments can be made by an reasonable design for spinneret micro-hole and high-speed spinnin g.
试验结果表明,通过合理的微孔设计,在高速纺丝条件下,可制得理想的狭扁形涤纶长丝。
When the machine is used to strengthen some chemical reactions such as cleanout of spinneret and SiO2, the result is certified better than using other methods.
用于强化其它一些化学反应，也有极好效果，用于清洗喷丝头，速度快，质量好，用于清洗二氧化硅，证明比其它方法效果更好。
The production technology that using the spinneret with 2808 holes to produce PET staple for roofing felt base cloth on HV452 spinning machine was discussed.
讨论了在HV452型纺丝机上采用2808孔喷丝板生产用于防水卷材基布的涤纶短纤维的生产工艺,指出提高成品纤维的强度、断裂伸长率、降低干热收缩率是满足防水卷材基布性能要求的关键。
The test showed, optimal clearing spinneret period improved the PET filament production status, reduced melt losing and updated full-package rate and product quality.
铲板周期的优化,有利于改善涤纶长丝的生产状况,降低熔体消耗,提高产品的满卷率和等级品率。
The process of spinpack of high-speed spinning in nyloy was probed into. The selection of spinneret,filter and sealing material were discussed especially.
本文对锦纶高速纺中组件工艺的选择作了探讨，着重讨论了喷丝板、过滤介质和密封介质的工艺配合。
The application experiments show they work better than traditional spinneret and can replace high-cost Au Pt spinnerets.
可纺性试验结果表明，其性能都达到或超过传统喷丝头，完全可以取代成本高昂的铂金喷丝头。
Part of the electronic apparatus,Medical equipment,Spare part production and maintenance of the automobile,motorcycle,engine,aeroplane,Metal press piese,oil,pump glib,compressor part and spinneret and washing,filtration of core of chemical fibre industry.
应用范围：电子电器零件、医疗器械、汽车、摩托车、机车、飞机零部件的生产与维修，金属冲压件、油泵油嘴、压缩机零件及化纤行业的喷丝板与过滤芯的清洗。
Rheological characteristic and shear rate of mesophase pitch in microhole passage of spinneret during melt spinning for preparation of large diameter mesophase pitch filament were investigated.
考察了大直径中间相沥青纤维熔纺过程中中间相沥青在喷丝板微孔区内的流动特性及剪切速率。
I plant professional sheet die. Sheet die. Linmo die. Spinneret lattice mold. Board hollow board (sunshine board) die. Variety of non-stop machine for rapid network with. Metering pumps. Distributor.
我厂专业片材模具.板材模具.淋膜模具.喷丝格子模具.板中空板（阳光板）模具.各种快速不停机换网器.计量泵．分配器
The die-swell mechanism of polycarbasilane(PCS) melt for a spinneret with Y-shaped orifice and the effect of die swelling of PCS on the profile degree (PD) of Y-shaped SiC were investigated.
摘要研究了聚碳矽烷(PCS)熔体在Y型喷丝孔中的挤出胀大机理、膨胀模型以及膨胀比对Y型碳化矽纤维异形度的影响。
Triple-arc-shaped spinneret was used in melt-spinning,and the hollow structure was formed in this process.C-shaped and round solid fibers could also be obtained when the parameters were changed.
结果表明:树脂提纯后可纺性能大大提高,只有在适当的熔纺条件下圆弧狭缝式喷丝板才能纺出中空结构的酚醛纤维,改变的熔纺参数,还可以纺出C形和实心圆形另外两种截面的酚醛纤维。
The key technical conditions for the design of shaped spinneret plates and the influence of various spinning conditions on fiber modification ratio during the shaped fiber development are discussed.
论述了异形喷丝板设计的技术关键条件和异形纤维开发中各种纺丝条件对纤维异形度的影响。
Results showed that the LCP phase structure was affected by the LCP concentration,viscosity,shear and elongational stress,size and shape of the spinneret,the use of compatible agent,etc.
结果显示在采用液晶高分子强化聚丙烯纤维的过程中,液晶相的浓度、粘度、熔体的剪切和拉伸张力、喷丝头形状、相容剂等因素对液晶相结构的形成有很大的影响。
In this article, the design of "-"spinneret of Polyester FDY was introduced.The effect of spinning temperature , spinning speed and quench process to the flat target of the filament were discussed.
介绍了涤纶FDY扁平丝“-”型喷丝板的工艺设计,主要讨论了纺丝温度、纺丝速度、侧吹风等工艺对纤维扁平度指标影响。
STUDY ON AUTOMATICALLY DESIGN SOFTWARE OF SPINNERET
喷丝板自动设计系统的研究
The state of development of spinneret
喷丝板的发展现状
Selection of spinneret for PET filament production
涤纶长丝生产中喷丝板的选用